Rectilinear viscoelastic flows in ducts

Michel Beaulne¹, Evan Mitsoulis²

¹Department of Chemical Engineering, University of Ottawa, Ottawa, Ontario, K1N 6N5, Canada.
²School of Mining Engineering and Metallurgy, National Technical University of Athens, Zografou 157 80, Athens, Greece.

DOI:

https://doi.org/10.7494/cmms.2008.3.0195

Abstract:

Axial flows in generalized ducts are studied for viscoelastic materials including a linear low-density polyethylene (LLDPE) melt. Viscoelasticity is described by an integral constitutive equation of the K-BKZ type with a spectrum of relaxation times, which fits well experimental data for the shear and elongational viscosities and the normal stresses as measured in shear flow. The K-BKZ model can be reduced to the Newtonian and Maxwell models with appropriate choice of the parameters. A new technique is developed where the Finger and Cauchy-Green tensors are simplified for axial flows, since particle tracking is only required in the flow z-direction (not required in the x-y coordinate plane). Numerical solutions are presented in two-dimensional cross-sectional geometries, namely square, concave square, and eccentric annulus, for different flow rate and pressure drop changes. For the Maxwell model, the dimensionless pressure drop is independent of the Weissenberg number and a function only of the geometry. For the K-BKZ model representing the LLDPE melt, the dimensionless pressure drop is reduced with increasing flow rate, hence Weissenberg number. The present results are offered as benchmark solutions for the imposition of entry velocity and stress profiles in three-dimensional ducts, when secondary flows are not present.

Cite as:

Beaulne, M., Mitsoulis, E., (2008). Rectilinear viscoelastic flows in ducts. Computer Methods in Materials Science, 8(3), 121 – 129. https://doi.org/10.7494/cmms.2008.3.0195

Article (PDF):

Keywords:

Viscoelasticity, K-BKZ constitutive equation, Maxwell model, Ducts, LLDPE melt

References:

Debbaut, B., Avalosse, T., Dooley, J., Hughes, K., 1997, On the development of secondary motions in straight channels induced by the second normal stress difference: experiments and simulations, J. Non-Newtonian Fluid Mech., 69, 255-271.

Dupont, S., Crochet, M.J., 1987, Swirling flows of viscoelastic fluids of the integral type in rheogoniometers, Chem. Eng. Comm., 53, 199-221.

Guillet, J., Revenu, P., Béreaux, Y., Clermont, J.-R., 1996, Experimental and numerical study of entry flow of polyethylene melts, Rheol. Acta, 35, 494-507.

Gervang, B., Larsen, P.S., 1991, Secondary flows in straight ducts of rectangular cross section, J. Non-Newtonian Fluid Mech., 39, 217-237.

Huilgol, R.R., Panizza, M.P., 1995, On the determination of the plug flow region in Bingham fluids through the application of variational inequalities, J. Non-Newtonian Fluid Mech., 58, 207-217.

Luo, X.-L., Mitsoulis, E., 1990a, An efficient algorithm for strain history tracking in finite element computations of non-Newtonian fluids with integral constitutive equations, Int. J. Num. Meth. Fluids, 11, 1015-1031.

Luo, X.-L., Mitsoulis, E., 1990b, A numerical study of the effect of elongational viscosity on vortex growth in contraction flows of polyethylene melts, J. Rheol., 34, 309-342.

Luo, X.-L., Tanner, R.I., 1986, A streamline element scheme for solving viscoelastic flow problems, Part II. Integral constitutive models, J. Non-Newtonian Fluid Mech., 22, 61-89.

Luo, X.-L., Tanner, R.I., 1988, Finite element simulation of long and short circular die extrusion experiments using integral models, Int. J. Num. Meth. Eng., 25, 9-22.

Middleman, S., 1965, Flow of power-law fluids in rectangular ducts, Trans. Soc. Rheol., 9, 83-95.

Normandin, M., Clermont, J.-R., Guillet, J., Raveyré, C., 1999, Three-dimensional extrudate swell: experimental and numerical study of a polyethylene melt obeying a memory integral equation, J. Non-Newtonian Fluid Mech., 87, 1-25.

Papanastasiou, A.C., Scriven, L.E., Macosko, C.W., 1983, An integral constitutive equation for mixed flows: viscoelastic characterization, J. Rheol., 27, 387-410.

Pham, T.V., Mitsoulis, E., 1998, Viscoplastic flows in ducts, Can. J. Chem. Eng., 76, 120-125.

Tanner, R.I., 2000, Engineering rheology, 2nd edn., Clarendon Press, Oxford.

Taylor, A.J., Wilson, S.D.R., 1997, Conduit flow of an incompressible, yield-stress fluid, J. Rheol., 41, 93-101.

Wachs, A., Clermont, J.R., Normandin, M., 1999, Fully-developed flow and temperature calculations for rheologically complex materials using a mapped circular domain, Eng. Comp., 16, 807-830.

Walton, I.C., Bittleston, S.H., 1991, The axial flow of a Bingham plastic in a narrow eccentric annulus, J. Fluid Mech., 222, 39-60.

Xue, S.C., Phan-Thien, N., Tanner, R.I., 1995, Numerical study of secondary flows of viscoelastic fluid in straight pipes by an implicit finite volume method, J. Non-Newtonian Fluid Mech., 59, 191-213.