Determination of the flow stress model of az80 mg alloy
Toko Tokunaga1
, Roman Kuziak2, Kiyotaka Matsuura3
1Research Fellow of Japan Society for the Promotion of Science, PhD student, Graduate School of Engineering, Hokkaido University, Sapporo, Hokkaido 060-8628, Japan.
2Institute for Ferrous Metallurgy, Gliwice, Poland.
3Faculty of Engineering, Hokkaido University, Sapporo, Hokkaido 060-8628, Japan.
DOI:
https://doi.org/10.7494/cmms.2014.2.0482
Abstract:
The flow stress model of AZ80 Mg alloy, whose grain size is approximately 30 μm, is created by interpreting the experimental results with the inverse analysis. Compression tests were conducted at temperatures of 523, 573 and 623 K and at strain rates of 0.01, 0.1 and 1 s-1. On the basis of the test results, the flow stress model of the Mg alloy was determined. As candidates of the flow stress model, three equations were selected and the coefficients in those equations were determined by using the inverse analysis and optimization process. In the optimization process, the measured and calculated loads were compared and the difference between them was minimized as objective functions. Consequently, the flow stress equation was chosen and the coefficients were determined. Reasonably good agreements of measured and calculated results were obtained with the equation which can be taken into account not only the softening but also the saturation of the flow stress due to the dynamic recrystallization.
Cite as:
Tokunaga, T., Kuziak, R., & Matsuura, K. (2014). Determination of the flow stress model of az80 mg alloy. Computer Methods in Materials Science, 14(2), 123 – 130. https://doi.org/10.7494/cmms.2014.2.0482
Article (PDF):
Keywords:
Computer simulation, Inverse analysis, Plastic deformation
Publication dates:
Received: 11.05.2014, accepted: 15.07.2014, published:
Publication type:
Original scientific paper
References:
Ambat, R., Aung, N.N., Zhou, W., 2000, Evaluation of microstructural effects on corrosion behaviour of AZ91D magnesium alloy, Corrosion Science, 42, 1433-1455.
Bhattacharya, R., Wynne, B.P., 2012, Scripta Materialia, Flow C N softening behavior during dynamic recrystallization in Mg–3Al–1Zn magnesium alloy, 67, 277-280. C
Davenport, S.B., Silk, N.J., Sparks, C.N., Sellars, C.M., 1999, L Development of constitutive equations for the modelling A R of hot rolling, Materials Science and Technology, 16, 1- 8. A M Gavrus A., Massoni E., Chenot J.L., 1996, An inverse analysis using a finite element model for identification of rheological parameters, Journal of Materials Processing D Technology, 60, 447-454. O H
Gontarz, A., Dziubinska, A., Okon, L., 2011, Determination of Friction Coefficients at Elevated Temperatures for Some M Al, Mg and Ti Alloys, Archives of Metallurgy and Mate- R rials, 56, 379-384. U
Gray, J.E., Luan, B., 2002, Protective coatings on magnesium P M and its alloys – a critical review, Journal of Alloys and O Compounds, 336, 88-113. C
Kang, S.H., Lee, Y.S., Lee, J.H., 2007, Effect of grain refinement of magnesium alloy AZ31 by severe plastic deformation on material characteristics, Journal of Materials Processing Technology, 201, 436-440.
Kobayashi, S., Oh, S.I., Altan, T., 1989, Metal forming and the finite element method, Oxford University Press, New York, Oxford.
Kowalski, B., Sellars, C.M., Pietrzyk, M., 2000, Development of a computer code for the interpretation of results of hot plane strain compression tests, ISIJ International, 40, 1230-1236.
Mehtedi, M. El., Musharavati, F., Spigarelli, S., 2014, Materials & Design, Modelling of the flow behaviour of wrought aluminium alloys at elevated temperatures by a new constitutive equation, 54, 869-873.
Pietrzyk, M., 2000, Finite element simulation of large plastic deformation, Journal of Materials Processing Technology, 106, 223-229.
Qua, G.Z., Shi, Y., Wang, Y.X., Kang, B.S., Ku, T.W., Song, W.J., 2011, Constitutive modeling for the dynamic recrystallization evolution of AZ80 magnesium alloy based on stress–strain data, Materials Science and Engineering, A528, 8051-8059.
Quan, G.Z., Shi, Y., Yu, C.T., Zhou, J., 2013, The Improved Arrhenius Model with Variable Parameters of Flow Behavior Characterizing for the As-Cast AZ80 Magnesium Alloy, Materials Research, 16, 785-791.
Sellars, C.M., 1979, Physical metallurgy of hot working, in: Hot working and forming processes, (eds), Sellars, C.M.,
Davies, G.J., The Metals Soc., London, 3-15.
Szeliga, D., Gawad, J., Pietrzyk, M., 2006, Inverse analysis for identification of rheological and friction models in metal forming, Computer Methods in Applied Mechanics and Engineering, 195, 6778-6798.
Tang, B., Yuan, Z., Cheng, G., Huang, L., Zheng, W., Xie, H., 2013, Experimental verification of tailor welded joining partners for hot stamping and analytical modeling of TWBs rheological constitutive in austenitic state, Materials Science and Engineering A, 585, 304-318.
Tokunaga, T., Matsuura, K., Ohno, M., 2012, Aluminum Coat- ing on Magnesium-Based Alloy by Hot Extrusion and Its Characteristics, Materials Transactions, 53, 1034- 1041.
Zheng, Q.G., Ying, T., Jie, Z., 2010, Dynamic softening behavior of AZ80 magnesium alloy during upsetting at different temperatures and strain rates, Proceedings of the C N Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, 224, 1707-1716. C
Zhou, H.T., Li, Q.B., Zhao, Z.K., Liu, Z.C., Wen, S.F., Wang, L Q.D., 2010, Hot workability characteristics of magnesium alloy AZ80—A study using processing map, Materials Science and Engineering A, 527, 2022-2026.