Simulation of steady-state extrusion through a hollow die using hyperxtrude FE software
Gang Liu1,2
, Ke Huang2, Jie Zhou1, Jurek Duszczyk1
1Department of Materials Science and Engineering, Delft University of Technology, Mekelweg 2, 2628 CD Delft, The Netherlands.
2School of Materials Science and Engineering, Harbin Institute of Technology, Harbin 150001, China.
DOI:
https://doi.org/10.7494/cmms.2011.2.0341
Abstract:
Die design for light-metal extrusion relies on the experience of the die designer. Die performance is only known after the die is manufactured and tested on the extrusion press. The die designer needs a tool that can provide an insight into metal flow through the die at the design stage. The extrusion process engineer needs the same tool to set optimum process parameters for the highest possible productivity and product quality. Computer simulation based on the finite element (FE) method can be such a tool, if software, material model, material data, boundary conditions and simulation parameters are all appropriate to represent the real process. The majority of commercial FE codes are based on the updated Lagrangian approach. Using these codes to simulate the industrial extrusion process with large billet and tooling sizes is time-consuming. HyperXtrude is an FE code based on the Arbitrary Lagrangian-Eulerian (ALE) approach and needs far less time to simulate the process in the steady state. The present study was aimed at assessing the capabilities of HyperXtrude to simulate the extrusion process through a porthole die to produce a rectangular tube. The effects of billet temperature, heat transfer between billet, die and air, and ram speed on the extrusion pressure and extrudate temperature were investigated. The extrudate temperature was found to keep rising during steady-state extrusion and the amplitude in the range of 40–90oC depending on the billet temperature. Being different from the heat transfer coefficient between the billet and die, the heat transfer coefficient between the die and surrounding air strongly influenced the extrudate temperature and extrusion pressure. Increasing ram speed led to monotonous increases of the workpiece temperatures inside the container and die welding chamber, while the effect on the pressures inside the container and die welding chamber was complicated by heat generation.
Cite as:
Liu, G., Huang, K., Zhou, J., & Duszczyk, J. (2011). Simulation of steady-state extrusion through a hollow die using hyperxtrude FE software. Computer Methods in Materials Science, 11(2), 259 – 264. https://doi.org/10.7494/cmms.2011.2.0341
Article (PDF):
Keywords:
Extrusion, Finite element method, Aluminium
References:
Arif, A.F.M., Sheikh, A.K., Qamar, S.Z., 2003, A study of die failure mechanisms in aluminium extrusion, J. Mater. Process. Technol., 134,318-328.
Donati, L., Tomesani, L., 2005, The effect of die design on the production and seam weld quality of extruded alumin¬ium profiles, J. Mater. Process. Technol. 164-165, 1025-1031.
Fang, G., Zhou, J., Duszczyk, J., 2009, FEM simulation of aluminium extrusion through two-hole multi-step pocket dies, J. Mater. Process. Technol. 209, 1891-1900.
Kloppenborg, T., Schikorra, M., Schomacker, M., Tekkaya, A.E., 2008, Numerical optimisation of bearing length in composite extrusion processes, Key Eng. Mater., 367, 47-54.
Li, L., Zhang, H., Zhou, J., Duszczyk, J., Li, G.Y., Zhong Z.H., 2008, Numerical and experimental study on the extrusion through a porthole die to produce a hollow magnesium profile, Mater. Design, 29, 1190-1198.
Liu, G., Zhou, J., Duszczyk, J., 2007a, Prediction and verification of temperature evolution as a function of ram speed during the extrusion of AZ31 alloy into a rectangular section, J. Mater. Process. Technol., 186, 2007, 191-199.
Liu, G., Zhou, J., Duszczyk, J., 2007b, Finite element analysis of magnesium extrusion to produce a cross-shaped pro¬file, ASME J. Manuf. Sci. Eng., 129, 607-614.
Liu, G., Zhou, J., Duszczyk, J., 2008, FE analysis of metal flow and weld seam formation in a porthole die during the ex¬trusion of a magnesium alloy into a square tube and the effect of ram speed on weld strength, J. Mater. Process. Technol. 200, 185-198.
Miles, N., Evans, G., Middleditch, A., 1997, Bearing lengths for extrusion dies: rationale, current practice and requirements for automation, J. Mater. Process. Technol., 72, 162-176.
Sheppard, T., 1999, Extrusion of Aluminium Alloys, Kluwer Academic Publishers, Dordrecht.